Augmenting the Performance of Evacuated Tube Solar Water Heater Using Perforated Wavy Tape

Authors

  • Punam Kumar Agade Department of Mechanical Engineering, Madhyanchal Professional University, Bhopal, 462044, Madhya Pradesh, India. https://orcid.org/0009-0000-7514-5261
  • Nitin Dubey Department of Mechanical Engineering, Madhyanchal Professional University, Bhopal, 462044, Madhya Pradesh, India.
  • Rahul Agrawal Department of Mechanical Engineering, Prestige Institute of Management and Research, Bhopal, 462022, India https://orcid.org/0009-0000-7514-5261

DOI:

https://doi.org/10.51646/jsesd.v14i1.264

Keywords:

Evacuated tube collector, Wavy tape, Energy, Energy Efficiency, Perforation, Water temperature.

Abstract

A significant portion of energy is wasted within the evacuated tube collector due to the formation of an inactive zone at the bottom of the tube, resulting in decreased efficiency. The current study presents an experimental investigation of the energetic and exergetic analysis of an evacuated tube solar water heater associated with perforated wavy tubes. A comparative analysis of conventional solar water heater and water heater with three different thermal enhancement methods was carried out: the use of wavy tape inserts (Plain WT), perforated wavy tape with 6 mm equilateral triangles (6 PWT), and perforated wavy tape with 9 mm equilateral triangles (9 PWT). The results showed that the insertion of wavy tapes improved the temperature of the ETC solar water heater's tank water as well as the temperature of the evacuated tubes. The highest hourly efficiency was recorded as 83.33% for the ETSC with 6 PWT, followed by 81.8%, 78.3%, and 75.6% for the ETSC with 9 PWT, ETSC with plain WT, and ETSC without WT, respectively. The effect of perforated wavy tape ETSC (6 PWT) resulted in a daily energy efficiency of 49.3%, which is greater than without WT (38.7%), with plain WT (44.9%), and with 9 PWT (47.8%). The average exergy efficiency of ETSC with 6 PWT was higher by 70.1%, 35.1%, and 13.1% compared to without WT, with plain WT, and with 9 PWT, respectively.

Downloads

Download data is not yet available.

Metrics

Metrics Loading ...

Author Biography

Rahul Agrawal, Department of Mechanical Engineering, Prestige Institute of Management and Research, Bhopal, 462022, India

Associate Professor in the Department of Mechanical Engineering at restige Institute of Management and Research, Bhopal, 462022, India

References

. Boafo, F.E., Kim, J.T. & Kim, J.H. (2017) Evaluating the impact of green roof evapotranspiration on annual building energy performance. International Journal of Green Energy, 14, 479–489. DOI: 10.1080/15435075.2016.1278375. DOI: https://doi.org/10.1080/15435075.2016.1278375

. Sofiane, M. I. H. O. U. B., & Abdelilah, B. E. N. A. H. M. E. D. (2024). Predicting the Impact of Different Cooling Systems on the Performance of Parabolic Trough Concentrating Solar Plant based on Real Data. Solar Energy and Sustainable Development Journal, 13(2), 264-285. DOI: https://doi.org/10.51646/jsesd.v13i2.267

. Reddy, P., Gupta, M.V.N.S., Nundy, S., Karthick, A. & Ghosh, A. (2020) Status of BIPV and BAPV system for less energy-hungry building in India—A review. Applied Sciences, 10, 2337. DOI: 10.3390/app10072337. DOI: https://doi.org/10.3390/app10072337

. Pasupathi, M.K., Alagar, K. MMM & Aritra, G. Characterization of hybridnano/paraffin organic phase change material for thermal energy storage applications in solar thermal systems, Energies 13–19 (2020) 5079. https://doi. DOI: 10.3390/en13195079. DOI: https://doi.org/10.3390/en13195079

. Aslan, M., Afif, B., Salmi, M., Merabet, B., Berka, M., & Masoud, S. (2025). Performance Enhancement of Microgrid Systems Using Backstepping Control for Grid Side Converter and MPPT Optimization. Solar Energy and Sustainable Development Journal, 14(1), 19-41. DOI: https://doi.org/10.51646/jsesd.v14i1.367

. Ahlem Z., Toufik S., Abderrezak M. (2024). Optimizing a Sustainable Power System with Green Hydrogen Energy Storage for Telecommunication Station Loads. Solar Energy and Sustainable Development Journal, 14(1), 19-41. DOI: https://doi.org/10.51646/jsesd.v14i1.366

. Saed, J., Abdunnabi, M., Essnid, A., & Buishi, A. (2017). New designed thermosyphon solar water heater with small sized parabolic trough collectors. Solar Energy and Sustainable Development Journal, 6(2), 30-41. DOI: https://doi.org/10.51646/jsesd.v6i2.44

. Ramasamy, K.K. & Srinivasan, P.S.S. (2012) Experimental investigation of forced and wind assisted domestic solar hot water systems. Proceedings of the Institution of Mechanical Engineers, Part C, 226, 154–160. DOI: 10.1177/0954406211413962. DOI: https://doi.org/10.1177/0954406211413962

. Agrawal, R. & Singh, K.D.P. (2021) Performance evaluation of double slope solar still augmented with binary eutectic phase change material and steel wool fibre, Sustainable Energy. Technology Assessment, 48, 101597. DOI: https://doi.org/10.1016/j.seta.2021.101597

. Nikhil Babu, P., Mohankumar, D., Manoj Kumar, P., Makeshkumar, M., Gokulnath, M., Gurubalaji, K., Harrish, G. & Ashok, M. (2021) Energy efficient refrigeration system with simultaneous heating and cooling. Materials Today: Proceedings, 45, 8188–8194. DOI: 10.1016/j.matpr.2021.03.072. DOI: https://doi.org/10.1016/j.matpr.2021.03.072

. Abdunnabi, M., Abusalama, A., Algamil, M., & Almontaser, M. (2018). Flat Plate based-Solar System with a tracking system. Solar Energy and Sustainable Development Journal, 7(1), 24-37. DOI: https://doi.org/10.51646/jsesd.v7i1.36

. Algareu, A., Abdunnabi, M., Mabruk, M., & Elmaghrabi, A. M. (2021). Legionella bacteria activity investigation in domestic water heating systems: Tripoli-Libya as a case study. Solar Energy and Sustainable Development Journal, 10(2), 11-20. DOI: https://doi.org/10.51646/jsesd.v10i2.114

. Kumar, A., Said, Z. & Bellos, E. (2021) An up-to-date review on evacuated tube solar collectors. Journal of Thermal Analysis and Calorimetry, 145, 2873–2889. DOI: 10.1007/s10973-020-09953-9. DOI: https://doi.org/10.1007/s10973-020-09953-9

. Kumar, A., Singh, K. D. P., & Agrawal, R. (2024). Intensification of thermal characteristics of flat plate solar water heater using triangular perforated wavy tape. Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science, 09544062241242589. DOI: https://doi.org/10.1177/09544062241242589

. Shukla, R. & Sumathy, K. P, Erickson J, gong. Recent advances in the solar water heating systems: A review. Renewable and Sustainable Energy Reviews, 2013, 173–190. DOI: https://doi.org/10.1016/j.rser.2012.10.048

. Kumar, B., Srivastava, G. P., Kumar, M., & Patil, A. K. (2018). A review of heat transfer and fluid flow mechanism in heat exchanger tube with inserts. Chemical Engineering and Processing-Process Intensification, 123, 126-137. DOI: https://doi.org/10.1016/j.cep.2017.11.007

. Sokhansefat, T., Kasaeian, A., Rahmani, K., Heidari, A.H., Aghakhani, F. & Mahian, O. (2018) Thermoeconomic and environmental analysis of solar flat plate and evacuated tube collectors in cold climatic conditions. Renewable Energy, 115, 501–508. DOI: 10.1016/j.renene.2017.08.057. DOI: https://doi.org/10.1016/j.renene.2017.08.057

. Touaba, O., Ait Cheikh, M.S., Slimani, M.E.A., Bouraiou, A., Ziane, A., Necaibia, A. & Harmim, A. (2020) Experimental investigation of solar water heater equipped with a solar collector using waste oil as absorber and working fluid. Solar Energy, 199, 630–644. DOI: 10.1016/j.solener.2020.02.064. DOI: https://doi.org/10.1016/j.solener.2020.02.064

. Taamneh, Y., Manokar, A.M., Thalib, M.M., Kabeel, A.E., Sathyamurthy, R. & Chamkha, A.J. (2020) Extraction of drinking water from modified inclined solar still incorporated with spiral tube solar water heater. Journal of Water Process Engineering, 38, 101613. DOI: 10.1016/j.jwpe.2020.101613. DOI: https://doi.org/10.1016/j.jwpe.2020.101613

. Saravanakumar, P.T., Arunkumar, S.P., Brailson Mansingh, B., Kumar, P.M., Ram Subbiah, E. & V.K. (2021) Investigating the effect of thermal cycling on thermal characteristics of the nano-silica based phase changing material (PCM). Materials Today: Proceedings. DOI: 10.1016/j.matpr.2021.09.095. DOI: https://doi.org/10.1016/j.matpr.2021.09.095

. King, M.F.L., Rao, P.N., Sivakumar, A., Mamidi, V.K., Richard, S., Vijayakumar, M., Arunprasath, K. & Kumar, P.M. (2022) Thermal performance of a double-glazed window integrated with a phase change material (PCM). Materials Today: Proceedings, 50, 1516–1521. DOI: 10.1016/j.matpr.2021.09.099. DOI: https://doi.org/10.1016/j.matpr.2021.09.099

. Iman, P. (2022) Using Rooftop Solar Heating to Supply Part of a High‐Rise Residential Building Heat in the Cold Climate of Iran: One‐Year Dynamic Analysis. International Transactions on Electrical Energy Systems, 2022.1, 9982264. DOI: https://doi.org/10.1155/2022/9982264

. Omeiza, L. A., Abid, M., Dhanasekaran, A., Subramanian, Y., Raj, V., Kozak, K., ... & Azad, A. K. (2023). Application of solar thermal collectors for energy consumption in public buildings–An updated technical review. Journal of Engineering Research. DOI: https://doi.org/10.1016/j.jer.2023.09.011

. Omidi, M., Farhadi, M. & Jafari, M. (2017) A comprehensive review on double pipe heat exchangers. Applied Thermal Engineering, 110, 1075–1090. DOI: 10.1016/j.applthermaleng.2016.09.027. DOI: https://doi.org/10.1016/j.applthermaleng.2016.09.027

. Balaji, K., Ganesh Kumar, P.G., Sakthivadivel, D., Vigneswaran, V.S. & Iniyan, S. (2019) Experimental investigation on flat plate solar collector using frictionally engaged thermal performance enhancer in the absorber tube. Renewable Energy, 142, 62–72. DOI: 10.1016/j.renene.2019.04.078. DOI: https://doi.org/10.1016/j.renene.2019.04.078

. Liu, S. & Sakr, M. (2013) A comprehensive review on passive heat transfer enhancements in pipe exchangers. Renewable and Sustainable Energy Reviews, 19, 64–81. DOI: 10.1016/j.rser.2012.11.021. DOI: https://doi.org/10.1016/j.rser.2012.11.021

. Sundar, L.S., Singh, M.K., Punnaiah, V. & Sousa, A.C.M. (2018) Experimental investigation of Al2O3/water nanofluids on the effectiveness of solar flat-plate collectors with and without twisted tape inserts. Renewable Energy, 119, 820–833. DOI: 10.1016/j.renene.2017.10.056. DOI: https://doi.org/10.1016/j.renene.2017.10.056

. Jaisankar, S., Radhakrishnan, T.K. & Sheeba, K.N. (2009) Experimental studies on heat transfer and friction factor characteristics of forced circulation solar water heater system fitted with helical twisted tapes. Solar Energy, 83, 1943–1952. DOI: 10.1016/j.solener.2009.07.006. DOI: https://doi.org/10.1016/j.solener.2009.07.006

. Morrison, G.L., Budihardjo, I. & Behnia, M. (2004) Water-in-glass evacuated tube solar water heaters. Solar Energy, 76, 135–140. DOI: 10.1016/j.solener.2003.07.024. DOI: https://doi.org/10.1016/j.solener.2003.07.024

. Dinesh, S.N., Ravi, S., Manoj Kumar, P., Subbiah, R., Karthick, A., Saravanakumar, P.T. & Aravinth Pranav, R. (2021) Study on an ETC solar water heater using flat and wavy diffuse reflectors. Materials Today: Proceedings, 47, 5228–5232. DOI: 10.1016/j.matpr.2021.05.561. DOI: https://doi.org/10.1016/j.matpr.2021.05.561

. Gunasekaran, N., Manoj Kumar, P., Raja, S., Sharavanan, S., Avinas, K., Aakash Kannan, P. & Gokul, S. (2021) Investigation on ETC solar water heater using twisted tape inserts. Materials Today: Proceedings, 47, 5011–5016. DOI: 10.1016/j.matpr.2021.04.586. DOI: https://doi.org/10.1016/j.matpr.2021.04.586

. Suri, A.R.S., Kumar, A. & Maithani, R. (2018) Convective heat transfer enhancement techniques of heat exchanger tubes: A review. International Journal of Ambient Energy, 39, 649–670. DOI: 10.1080/01430750.2017.1324816. DOI: https://doi.org/10.1080/01430750.2017.1324816

. Nanan, K., Wongcharee, K., Nuntadusit, C. & Eiamsa-ard, S. (2012) Forced convective heat transfer by swirling impinging jets issuing from nozzles equipped with twisted tapes. International Communications in Heat and Mass Transfer, 39, 844–852. DOI: 10.1016/j.icheatmasstransfer.2012.05.002. DOI: https://doi.org/10.1016/j.icheatmasstransfer.2012.05.002

. Ponnada, S., Subrahmanyam, T. & Naidu, S.V. (2019) A comparative study on the thermal performance of water in a circular tube with twisted tapes, perforated twisted tapes and perforated twisted tapes with alternate axis. International Journal of Thermal Sciences, 136, 530–538. DOI: 10.1016/j.ijthermalsci.2018.11.008. DOI: https://doi.org/10.1016/j.ijthermalsci.2018.11.008

. Eiamsa-Ard, S., Nanan, K., Wongcharee, K., Yongsiri, K. & Thianpong, C. (2014b) Thermohydraulic performance of heat exchanger tube twisted tapes thermohydraulic performance of heat exchanger tube equipped with single-. Double Triple-Helical Twisted Tapes;37-41. DOI: 10.1080/00986445.2013.858038. DOI: https://doi.org/10.1080/00986445.2013.858038

. Al-Fahed, S., Chamra, L.M., & Chakroun W. (1998) Pressure drop and heat transfer comparison for both microfin tube and twisted-tape inserts in laminar flow. Exp Therm Fluid Sci, 18, 323–333. DOI: https://doi.org/10.1016/S0894-1777(98)10037-7

. Kumar, B., Patil, A.K., Kumar, M. (2020) Performance enhancement by perforated twisted tape tube insert with single and double v cuts in a heat exchanger tube. Heat Transf Re 51, 395–406. DOI: https://doi.org/10.1615/HeatTransRes.2019029789

. Piriyarungrod, N., Eiamsa-Ard, S., Thianpong, C., Pimsarn, M., & Nanan, K. J. C. E. (2015). Heat transfer enhancement by tapered twisted tape inserts. Chemical Engineering and Processing: Process Intensification, 96, 62-71. DOI: https://doi.org/10.1016/j.cep.2015.08.002

. Wongcharee, K. and Eiamsa-Ard, S. (2011) Heat transfer enhancement by twisted tapes with alternate-axes and triangular, rectangular and trapezoidal wings. Chemical Engineering and Processing: Process Intensification, 50(2), 211-219. DOI: https://doi.org/10.1016/j.cep.2010.11.012

. Jouybari, N.F. & Lundström, T.S. (2020) Performance improvement of a solar air heater by covering the absorber plate with a thin porous material. Energy, 190, 116437. DOI: https://doi.org/10.1016/j.energy.2019.116437

. Papadimitratos A, Sobhansarbandi S, Pozdin V, Zakhidov A, Hassanipour F. (2016) Evacuated tube solar collectors integrated with phase change materials. Sol Energy, 129:10-19. DOI: https://doi.org/10.1016/j.solener.2015.12.040

. Krishnavel, V., Karthick, A. & Murugavel, K.K. (2014) Experimental analysis of concrete absorber solar water heating systems. Energy and Buildings, 84, 501–505. DOI: 10.1016/j.enbuild.2014.08.025. DOI: https://doi.org/10.1016/j.enbuild.2014.08.025

. Tang, R. & Yang, Y. (2014) Nocturnal reverse flow in water-in-glass evacuated tube solar water heaters. Energy Conversion and Management, 80, 173–177. DOI: 10.1016/j.enconman.2014.01.025. DOI: https://doi.org/10.1016/j.enconman.2014.01.025

. Agrawal, R., Singh, K.D.P., Paswan, M.K. (2020) Review on Enhancement of Thermal Conductivity of Phase Change Materials with Nano-Particle in Engineering Applications. Materials Today: Proceedings, 22, 1617–1627. DOI: https://doi.org/10.1016/j.matpr.2020.02.159

. Ismail, K.A.R. & Abogderah, M.M. (1998) Performance of a heat pipe solar collector. Journal of Solar Energy Engineering. Transaction Publishing of ASME, 120, 51–59. DOI: 10.1115/1.2888047. DOI: https://doi.org/10.1115/1.2888047

. Jafaryar, M., Said, Z. & Sheikholeslami, M. (2022) Hybrid nanofluid turbulent transportation through a tube with an innovative twisted tape combined with helical fins heat sink. Sustainable Energy Technologies and Assessments, 53, 102–702. DOI: 10.1016/j.seta.2022.102702. DOI: https://doi.org/10.1016/j.seta.2022.102702

. Rajan, A. & Prasad, L. (2022) Performance investigation of heat exchanger tube fitted with hyperbolic-cut twisted tape in turbulent flow. Proceedings of the Institution of Mechanical Engineers, Part C, 236, 8134–8149. DOI: 10.1177/09544062221085102. DOI: https://doi.org/10.1177/09544062221085102

. Brahim, T., Dhaou, M.H. & Jemni, A. (2014) Theoretical and experimental investigation of plate screen mesh heat pipe solar collector. Energy Conversion and Management, 87, 428–438. DOI: 10.1016/j.enconman.2014.07.041. DOI: https://doi.org/10.1016/j.enconman.2014.07.041

. Joo, H.J., Kwak, H.Y. & Kong, M. (2022) Effect of twisted tape inserts on thermal performance of heat pipe evacuated-tube solar thermal collector. Energy, 254, 124307. DOI: 10.1016/j.energy.2022.124307. DOI: https://doi.org/10.1016/j.energy.2022.124307

. Murugesan, P., Mayilsamy, K. & Suresh, S. (2010) Heat Transfer and friction factor studies in a circular tube fitted with twisted tape consisting of wire-nails. Chinese Journal of Chemical Engineering, 18, 1038–1042. DOI: 10.1016/S1004-9541(09)60166-X. DOI: https://doi.org/10.1016/S1004-9541(09)60166-X

. Chaurasia, S.R. & Sarviya, R. (2021) Numerical and experimental thermal performance with entropy generation analysis on tube with helical screw tape inserts at number of strips in turbulent flow. Proceedings of the Institution of Mechanical Engineers, Part C, 235, 1057–1070. DOI: 10.1177/0954406220937734. DOI: https://doi.org/10.1177/0954406220937734

. Budihardjo, I. Evacuated Tubular Solar Water Heaters (Doctoral dissertation, UNSW Sydney) (2005).

. Khan, M. M. A.; Ibrahim, N. I.; Saidur, R.; Mahbubul, I. M.; Al-Sulaiman, F. A. Performance Assessment of a Solar Powered Ammonia–Water Absorption Refrigeration System with Storage Units. Energy Convers. Manag. 2016, 126, 316–328. DOI: https://doi.org/10.1016/j.enconman.2016.08.004

. Bracamonte, J., Parada, J., Dimas, J. & Baritto, M. (2015) Effect of the collector tilt angle on thermal efficiency and stratification of passive water in glass evacuated tube solar water heater. Applied Energy, 155, 648–659. DOI: 10.1016/j.apenergy.2015.06.008. DOI: https://doi.org/10.1016/j.apenergy.2015.06.008

. Li, F.F., Diao, Y.H., Zhao, Y.H., Zhu, T. & Liu, J. (2016) Experimental study on the thermal performance of a new type of thermal energy storage based on flat micro-heat pipe array. Energy Conversion and Management, 112, 395–403. DOI: 10.1016/j.enconman.2016.01.039. DOI: https://doi.org/10.1016/j.enconman.2016.01.039

. Manoj Kumar, P.M. & Mylsamy, K. (2019) Experimental investigation of solar water heater integrated with a nanocomposite phase change material. Journal of Thermal Analysis and Calorimetry, 136, 121–132. DOI: 10.1007/s10973-018-7937-9. DOI: https://doi.org/10.1007/s10973-018-7937-9

. Petela, R. (2003) Exergy of undiluted thermal radiation. Solar Energy, 74, 469–488. DOI: 10.1016/S0038-092X(03)00226-3. DOI: https://doi.org/10.1016/S0038-092X(03)00226-3

. Vijay, R., Vijayakumar, P., Kumaresan, G. (2021) Performance study of flat plate solar collector integrated with twisted tape inserts. Materials Today: Proceedings, 45:1222-1226. DOI: https://doi.org/10.1016/j.matpr.2020.04.249

Downloads

Published

2025-02-10

How to Cite

Agade, P. K., Dubey, N. ., & AGRAWAL, R. (2025). Augmenting the Performance of Evacuated Tube Solar Water Heater Using Perforated Wavy Tape. Solar Energy and Sustainable Development Journal, 14(1), 258–278. https://doi.org/10.51646/jsesd.v14i1.264

Issue

Section

Articles